manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

possible—at least half a tank. Do not add less than five gallons (18.9L)
when refueling. You should drive the vehicle immediately after refueling
for at least 5 miles (8 km) to allow the vehicle to adapt to the change in
ethanol concentration.

If you exclusively use E85 fuel, it is recommended to fill the fuel tank
with regular unleaded gasoline at each scheduled oil change.

Fuel quality

If you are experiencing starting, rough idle or hesitation driveability
problems during a cold start, try a different brand of “Regular” unleaded
gasoline. Premium unleaded gasoline is not recommended for vehicles
designed to use “Regular” unleaded gasoline because it may cause these
problems to become more pronounced. If the problems persist, see your
authorized dealer.

Do not add aftermarket fuel additive products to your fuel tank. It
should not be necessary to add any aftermarket products to your fuel
tank if you continue to use high quality fuel of the recommended octane
rating. These products have not been approved for your engine and
could cause damage to the fuel system. Repairs to correct the effects of
using an aftermarket product in your fuel may not be covered by your
warranty.

Many of the world’s automakers approved the World-Wide Fuel Charter
that recommends gasoline specifications to provide improved
performance and emission control system protection for your vehicle.
Gasolines that meet the World-Wide Fuel Charter should be used when
available. Ask your fuel supplier about gasolines that meet the
World-Wide Fuel Charter.

FFV engine (if equipped)

Flex fuel vehicles have a yellow bezel around the fuel fill inlet.

It is best not to alternate repeatedly between gasoline and E85. If you do
switch fuels, it is recommended that you add as much fuel as
possible—at least half a tank. Do not add less than five gallons (18.9L)
when refueling. You should drive the vehicle immediately after refueling
for at least 5 miles (8 km) to allow the vehicle to adapt to the change in
ethanol concentration.

If you exclusively use E85 fuel, it is recommended to fill the fuel tank
with regular unleaded gasoline at each scheduled oil change.

Maintenance and Specifications

297

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Brand: DANA Pages: 42
dallara F305 Manual preview
F305
Brand: dallara Pages: 37
Yakima BOA Installation Instructions Manual preview
BOA
Brand: Yakima Pages: 8
Kargo Master 80070 Assembly Lnstructions preview
80070
Brand: Kargo Master Pages: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Brand: Kargo Master Pages: 21
Kargo Master 40201 Installation Manual preview
40201
Brand: Kargo Master Pages: 4
Whispbar K925W Fitting Instructions Manual preview
K925W
Brand: Whispbar Pages: 15
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Brand: Raytel LLC Pages: 40
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Brand: Eaton Pages: 18
Condor T-RAMP Quick Start Manual preview
T-RAMP
Brand: Condor Pages: 2
TrailFX 2123131 Quick User Manual preview
2123131
Brand: TrailFX Pages: 2
Honda 08V31-TE0-100A Installation Instructions Manual preview
08V31-TE0-100A
Brand: Honda Pages: 10
Hella 2DA 008 136-031 Mounting Instructions preview
2DA 008 136-031
Brand: Hella Pages: 2
Bracketron Multi Vehicle Mount MVM-35-05 Installation Manual preview
Multi Vehicle Mount MVM-35-05
Brand: Bracketron Pages: 4
Whispbar K723W Fitting Instructions Manual preview
K723W
Brand: Whispbar Pages: 77
Toyota Tacoma 05 Brochure & Specs preview
Tacoma 05
Brand: Toyota Pages: 26

Brands by name

Popular brands

Load more brands