Mercury 2010 Milan Owner'S Manual Download Page 93 | Manualshive

Page: 93 / 330

background image

REMOTE ENTRY SYSTEM

The Integrated Keyhead Transmitter (IKT) complies with part 15 of the
FCC rules and with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.

The typical operating range for your IKT is approximately 33 feet
(10 meters). A decrease in operating range could be caused by:

•

weather conditions,

•

nearby radio towers,

•

structures around the vehicle, or

•

other vehicles parked next to your vehicle.

The IKT allows you to:

•

remotely unlock the vehicle
doors.

•

remotely lock all the vehicle
doors.

•

remotely open the trunk.

•

activate the personal alarm.

•

arm and disarm the perimeter
anti-theft system.

•

operate the illuminated entry
feature.

The remote entry lock/unlock feature operates in any ignition position
except while the key is held in the start position. The panic feature
operates with the key in the off position.

If there are problems with the remote entry system, make sure to take

ALL Integrated Keyhead Transmitters

with you to the authorized

dealer in order to aid in troubleshooting the problem.

Locks and Security

93

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
91
92
93
94
95
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: CAMPARK Pages: 20

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: Mercedes-Benz Pages: 54

Brand: Pacbrake Pages: 6

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

51 47 0 027 792

Brand: BMW Pages: 7

Brand: Ford Pages: 728

Brand: Westin Pages: 5

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

TuneBase F8Z442

Brand: Belkin Pages: 162

Brand: Great day Pages: 5

Brand: Ford Pages: 312

Brand: Camcar Pages: 2

Brand: Chevrolet Pages: 103

Brand: Peak Pages: 8

Brand: Renault Pages: 239

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands