Mercury 2010 Milan Owner'S Manual Download Page 117 | Manualshive

Page: 117 / 330

background image

To lower the seatback(s), pull the
release handle(s) located inside the
trunk.

Fold the seatback(s) down.

WARNING:

Before returning the seatback to its original

position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original
position, pull on the seatback to ensure that it has fully latched. An
unlatched seat may become dangerous in the event of a sudden stop or
collision.

Make sure that the safety belt for the rear center passenger is properly
routed over the rear seatback.

Seating and Safety Restraints

117

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
115
116
117
118
119
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: EAL Pages: 4

Brand: Eclipse Pages: 6

Brand: Barker Pages: 2

Brand: Kuda-Phonebase Pages: 3

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Cadillac Pages: 522

Brand: Prorack Pages: 20

Brand: Havis Pages: 5

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

FABIA II TMB PS 035

Brand: Skoda Pages: 16

Brand: Hyundai Pages: 168

Brand: Honda Pages: 4

Brand: Pet Gear Pages: 4

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands