manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

Always inflate your tires to the Ford recommended inflation pressure
even if it is less than the maximum inflation pressure information found
on the tire. The Ford recommended tire inflation pressure is found on
the Safety Compliance Certification Label or Tire Label which is located
on the B-Pillar or the edge of the driver’s door. Failure to follow the tire
pressure recommendations can cause uneven treadwear patterns and
adversely affect the way your vehicle handles.

Maximum Permissible Inflation Pressure

is the tire manufacturer’s

maximum permissible pressure and/or the pressure at which the
maximum load can be carried by the tire. This pressure is normally
higher than the manufacturer’s recommended cold inflation pressure
which can be found on the Safety Compliance Certification Label or Tire
Label which is located on the B-Pillar or the edge of the driver’s door.
The cold inflation pressure should never be set lower than the
recommended pressure on the Safety Compliance Certification Label or
Tire Label.

When weather temperature changes occur, tire inflation pressures also
change. A 10°F (6°C) temperature drop can cause a corresponding drop
of 1 psi (7 kPa) in inflation pressure. Check your tire pressures
frequently and adjust them to the proper pressure which can be found
on the Safety Compliance Certification Label or Tire Label.

To check the pressure in your tire(s):

1. Make sure the tires are cool, meaning they are not hot from driving
even a mile.

If you are checking tire pressure when the tire is hot, (i.e. driven more
than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are
hot from driving and it is normal for pressures to increase above
recommended cold pressures. A hot tire at or below recommended cold
inflation pressure could be significantly under-inflated.

Note:

If you have to drive a distance to get air for your tire(s), check

and record the tire pressure first and add the appropriate air pressure
when you get to the pump. It is normal for tires to heat up and the air
pressure inside to go up as you drive.

2. Remove the cap from the valve on one tire, then firmly press the tire
gauge onto the valve and measure the pressure.

Tires, Wheels and Loading

170

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Samsung HF1000 User Manual preview
HF1000
Brand: Samsung Pages: 133
Acdeos AXS FL Manual preview
AXS FL
Brand: Acdeos Pages: 38
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Brand: GMC Pages: 425
Ford E-Transit 2022 Manual preview
E-Transit 2022
Brand: Ford Pages: 22
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Brand: CITROËN Pages: 301
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
NavLinkz RL4-ELINK Manual preview
RL4-ELINK
Brand: NavLinkz Pages: 23
Thule 953000 Instructions Manual preview
953000
Brand: Thule Pages: 8
Saab 32 025 907 Installation Instructions Manual preview
32 025 907
Brand: Saab Pages: 37
BMW 84 61 0 028 926 Installation Instructions Manual preview
84 61 0 028 926
Brand: BMW Pages: 13
Roadtrek SS Agile 2017 Owner'S Manual preview
SS Agile 2017
Brand: Roadtrek Pages: 61
Menabo KIT+1 MERAK Fitting Instructions Manual preview
KIT+1 MERAK
Brand: Menabo Pages: 8
Mercedes-Benz 2013 S-CLASS Owner'S Manual preview
2013 S-CLASS
Brand: Mercedes-Benz Pages: 493
Honda 08P00-T7S-600 Installation Instructions preview
08P00-T7S-600
Brand: Honda Pages: 5
Navman F-Series B2+ User Manual preview
F-Series B2+
Brand: Navman Pages: 10
Cruiser Consoles BUSHMAN 15L ROADIE fridge Base console Installation Instructions Manual preview
BUSHMAN 15L ROADIE fridge Base console
Brand: Cruiser Consoles Pages: 6
Honda Civic Coupe 2009 Owner'S Manual preview
Civic Coupe 2009
Brand: Honda Pages: 414

Brands by name

Popular brands

Load more brands