manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

When inflating your tires

When putting air into your tires (such as at a gas station or in your
garage), the Tire Pressure Monitoring System may not respond
immediately to the air added to your tires.

It may take up to two minutes of driving over 20 mph (32 km/h) for the
light to turn OFF after you have filled your tires to the recommended
inflation pressure.

How temperature affects your tire pressure

The Tire Pressure Monitoring System (TPMS) monitors tire pressure in
each pneumatic tire. While driving in a normal manner, a typical
passenger tire inflation pressure may increase approximately 2 to 4 psi
(14 to 28 kPa) from a cold start situation. If the vehicle is stationary
over night with the outside temperature significantly lower than the
daytime temperature, the tire pressure may decrease approximately 3 psi
(21 kPa) for a drop of 30°F (17°C) in ambient temperature. This lower
pressure value may be detected by the TPMS as being significantly lower
than the recommended inflation pressure and activate the TPMS warning
for low tire pressure. If the low tire pressure warning light is ON, visually
check each tire to verify that no tire is flat. (If one or more tires are flat,
repair as necessary.) Check air pressure in the road tires. If any tire is
under-inflated, carefully drive the vehicle to the nearest location where
air can be added to the tires. Inflate all the tires to the recommended
inflation pressure.

SNOW TIRES AND CHAINS

WARNING:

Snow tires must be the same size, load index, speed

rating as those originally provided by Ford. Use of any tire or

wheel not recommended by Ford can affect the safety and performance
of your vehicle, which could result in an increased risk of loss of vehicle
control, vehicle rollover, personal injury and death. Additionally, the use
of non-recommended tires and wheels could cause steering, suspension,
axle or transfer case/power transfer unit failure.

The tires on your vehicle have all weather treads to provide traction in
rain and snow. However, in some climates, you may need to use snow
tires and chains. If you need to use chains, it is recommended that steel
wheels (of the same size and specifications) be used, as chains may chip
aluminum wheels.

Tires, Wheels and Loading

186

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Code 3 WingMan Installation & Operation Manual preview
WingMan
Brand: Code 3 Pages: 8
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Brand: E&G Classics Pages: 2
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Brand: Oldsmobile Pages: 348
Gator GT700SD User Manual preview
GT700SD
Brand: Gator Pages: 6
F.lli Menabo CROSS 2 Assembly Instructions Manual preview
CROSS 2
Brand: F.lli Menabo Pages: 16
Volvo S90 - ACCESSORY PANEL Owner'S Manual Supplement preview
S90 - ACCESSORY PANEL
Brand: Volvo Pages: 166
Thule Kit 1312 Instructions Manual preview
Kit 1312
Brand: Thule Pages: 8
Volvo Ski box Installation Instructions Manual preview
Ski box
Brand: Volvo Pages: 7
Overland Outfitters SHERPA SADDLE BAG JL Installation Instructions preview
SHERPA SADDLE BAG JL
Brand: Overland Outfitters Pages: 2
Whispbar K519W Fitting Instructions Manual preview
K519W
Brand: Whispbar Pages: 15
Ranger design 5047 Installation Manual preview
5047
Brand: Ranger design Pages: 6
Stack ROLL POD Installation Manual preview
ROLL POD
Brand: Stack Pages: 4
N2MB Racing WOT Box Installation Instructions Manual preview
WOT Box
Brand: N2MB Racing Pages: 13

Brands by name

Popular brands

Load more brands