manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

High fluid level

Type A

Type B

Fluid levels above the zone, identified by the arrows in the above figures,
may result in transmission failure. An overfill condition of transmission
fluid may cause shift and/or engagement concerns and/or possible damage.

High fluid levels can be caused by an overheating condition.

Adjusting automatic transmission fluid levels

Before adding any fluid, make sure the correct type is used. The type of
fluid used is normally indicated on the dipstick blade. Refer to

Maintenance product specifications and capacities

in this chapter.

Use of a non-approved automatic transmission fluid may cause
internal transmission component damage.

If necessary, add fluid in 1/2 pint (250 ml) increments through the filler
tube until the level is correct.

Type A

Type B

If an overfill occurs, excess fluid should be removed by an authorized
dealer.

DO NOT ADD

ADD (CHECK HOT)

DO NOT ADD

ADD (CHECK HOT)

Maintenance and Specifications

308

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Warrior Products 10936 Installation Instructions preview
10936
Brand: Warrior Products Pages: 3
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Brand: Quadratec Pages: 20
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Brand: Raytel LLC Pages: 40
Chevrolet 1999 Malibu Owner'S Manual preview
1999 Malibu
Brand: Chevrolet Pages: 344
Prorack K692 Fitting Instructions Manual preview
K692
Brand: Prorack Pages: 15
AA Products SR-A260 Instruction Manual preview
SR-A260
Brand: AA Products Pages: 4
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Brand: Ford Pages: 368
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Brand: Audiovox Pages: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Brand: Mercedes-Benz Pages: 2
Westin 25-0560 Instructions preview
25-0560
Brand: Westin Pages: 2
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Brand: HAUL MASTER Pages: 8
JKS OGS125 Installation Instructions preview
OGS125
Brand: JKS Pages: 3
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Brand: mtf TRANSPORT SYSTEM Pages: 9
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Brand: Volvo Pages: 262
Jaeger 21360508 Fitting Instructions Manual preview
21360508
Brand: Jaeger Pages: 13
Draw tite 77971 Installation Instructions preview
77971
Brand: Draw tite Pages: 4
Audi 2001 A3 Quick Reference Manual preview
2001 A3
Brand: Audi Pages: 4
Thule Brink 5324 Fitting Instructions Manual preview
Brink 5324
Brand: Thule Pages: 15

Brands by name

Popular brands

Load more brands