manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

To reinstall the head restraint, line
the posts up in the holes on the seat
back with the head restraint strap
facing the outside of the vehicle and
push down until the head restraint
locks into place. Lift gently to
ensure it is locked into place.

Refer to

Rear adjustable head restraints

earlier in this chapter for

more information.

WARNING:

If the head restraint has been removed from a

seating position to accommodate a high back child restraint, the

head restraint must be re-installed prior to use of the seat by any other
occupant in order to reduce the risk of personal injury in the event of
a collision.

Check to make sure the child seat is properly secured before each use.
Children 12 and under should be properly restrained in a rear seating
position whenever possible. If all children cannot be seated and
restrained properly in a rear seating position, properly restrain the
largest child in the front seat.

Seating and Safety Restraints

154

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

U.S. General 97845 Set Up And Operating Instructions preview
97845
Brand: U.S. General Pages: 5
Jeep Compass Owner'S Handbook Manual preview
Compass
Brand: Jeep Pages: 322
Jeep Compass Repair Manual preview
Compass
Brand: Jeep Pages: 341
Jeep Compass Operating Information Manual preview
Compass
Brand: Jeep Pages: 310
Jeep Compass Information Manual preview
Compass
Brand: Jeep Pages: 189
Jeep Compass Review preview
Compass
Brand: Jeep Pages: 26
Jeep Compass Overview preview
Compass
Brand: Jeep Pages: 21
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Brand: Jeep Pages: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Brand: Jeep Pages: 80
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Brand: Jeep Pages: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Brand: Jeep Pages: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Brand: Jeep Pages: 558
Yakima K831 Manual preview
K831
Brand: Yakima Pages: 8
Thule 1809 Instruction Manual preview
1809
Brand: Thule Pages: 4
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Brand: ULTIMATE SPEED Pages: 10
POOL-LINE 110050 Assembly Instructions preview
110050
Brand: POOL-LINE Pages: 2
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Brand: Anker Technology Pages: 8
Pontiac 2007 G6 Owner'S Manual preview
2007 G6
Brand: Pontiac Pages: 486

Brands by name

Popular brands

Load more brands