Mercury 2010 Milan Owner'S Manual Download Page 68

Page: 68 / 330

Replacing high-mount brake lamp bulb

1. Make sure the ignition control is
in the off position.

2. Open the trunk and reach
underneath the package tray to
locate the lamp assembly.

3. Remove the bulb socket by
rotating it counterclockwise, then
pull it out of the lamp assembly.

4. Pull the bulb straight from the
socket and push in the new bulb.

5. Install the bulb socket into the lamp assembly by rotating it clockwise.

Replacing license plate lamp bulbs

1. Make sure the headlamp switch is
in the off position.

2. Remove the screws from the
license plate lamp assembly.

3. Remove bulb socket by turning
counterclockwise.

4. Carefully pull the bulb out from
the socket.

Install new bulb(s) in reverse order.

Replacing fog lamp bulbs

1. Make sure the fog lamp switch is
in the off position.

2. From underneath the vehicle,
partially remove the tire splash
shield by removing four drive
screws.

After removing to allow free access
to the front fog lamp bulb and
electrical wire harness, the splash shield flap can be repositioned.

Lights

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands

Mercury 2010 Milan, Owner'S Manual

Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands