manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

•

The gearshift is in neutral (manual transmission)

•

The ignition switch is in the off position

•

The driver and front passenger safety belts are unbuckled

WARNING:

While the design allows you to deactivate your

Belt-Minder

威

, this system is designed to improve your chances of

being safely belted and surviving an accident. We recommend you
leave the Belt-Minder

威

system activated for yourself and others who

may use the vehicle. To reduce the risk of injury, do not
deactivate/activate the Belt-Minder

威

feature while driving the vehicle.

1. Turn the ignition switch to the on position. DO NOT START THE
ENGINE.

2. Wait until the safety belt warning light turns off (approximately one
minute).

•

Step 3 must be completed within 30 seconds after the safety belt
warning light turns off.

3. For the seating position being disabled, buckle then unbuckle the
safety belt three times at a moderate speed, ending in the unbuckled
state. Step 3 must be completed within 30 seconds after the safety belt
warning light turns off.

•

After Step 3, the restraint system warning light (airbag light) will be
turned on for three seconds.

4. Within approximately seven seconds of the light turning off, buckle
then unbuckle the safety belt.

•

This will disable the Belt-Minder

威

feature for that seating position if it

is currently enabled. As confirmation, the restraint system warning
light will flash four times per second for three seconds.

•

This will enable the Belt-Minder

威

feature for that seating position if it

is currently disabled. As confirmation, the restraint system warning
light will flash four times per second for three seconds, followed by
three seconds with the light off, then followed by the restraint system
warning light flashing four times per second for three seconds again.

Seating and Safety Restraints

131

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Qube AP1 Supplemental Instructions preview
AP1
Brand: Qube Pages: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Brand: Cadillac Pages: 32
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Brand: APS Auto Parts Specialist Pages: 3
Würth 071554055 User Instructions preview
071554055
Brand: Würth Pages: 36
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Brand: Xblitz Pages: 30
Alpitronic Hypercharger HYC 075 Operation Instructions And Installation Manual preview
Hypercharger HYC 075
Brand: Alpitronic Pages: 64
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Brand: Calitop Pages: 5
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Brand: Easee Pages: 12
Buick Electra 225 1965 Service Manual preview
Electra 225 1965
Brand: Buick Pages: 914
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Brand: Dodge Pages: 444
Honda 2006 Accord Owner'S Manual preview
2006 Accord
Brand: Honda Pages: 569
Brodit Getac T800 Quick Start Manual preview
Getac T800
Brand: Brodit Pages: 2
Saturn 2009 OUTLOOK Owner'S Manual preview
2009 OUTLOOK
Brand: Saturn Pages: 432
Thule Follow me RAPID INTRACKER Fitting Instructions Manual preview
Follow me RAPID INTRACKER
Brand: Thule Pages: 8
Brodit 841488 Quick Start Manual preview
841488
Brand: Brodit Pages: 2
AA Products RB0008 Instruction Manual preview
RB0008
Brand: AA Products Pages: 6
Chevrolet 2003 Suburban Owner'S Manual preview
2003 Suburban
Brand: Chevrolet Pages: 516
Jeep 2009 Wrangler Owenrs Manual preview
2009 Wrangler
Brand: Jeep Pages: 502

Brands by name

Popular brands

Load more brands