Mercury 2010 Milan Owner'S Manual Download Page 64

Page: 64 / 330

For passenger side replacement of this bulb, do the following:

1. Make sure headlamp control is in the off position, then open the hood.

2. At the wheel well, remove the
press pins from the splash shield.

3. Reaching through the wheel well,
remove the rubber bulb access
cover from the housing.

4. Remove the bulb socket by rotating it counterclockwise, then pull it
straight out of the lamp assembly.

5. Disconnect the electrical
connector from the bulb socket and
discard the old bulb socket.

Lights

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands

Mercury 2010 Milan, Owner'S Manual

Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands