manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

The side air curtains are mounted to the sheet metal above the first and
second row seats. In certain lateral collisions, the air curtain and
seat-mounted side airbag on the side affected by the collision will be
inflated, except that the passenger sensing system will deactivate the
passenger seat-mounted side airbag if it detects an empty unbuckled
passenger seat or an unbuckled child or small person in the passenger
seat. The air curtain was designed to inflate between the side window
area and occupant to further enhance the protection provided to
occupants in side impact collisions. The seat-mounted side airbag was
designed to inflate between the door panel and occupant to further
enhance the protection provided occupants in side impact collisions.

The side air curtain system SRS is designed to activate when the vehicle
sustains lateral deceleration sufficient to cause the sensors to close an
electrical circuit that initiates air curtain and seat-mounted side airbag
inflation.

The fact that the side air curtain and seat-mounted side airbag did not
inflate in a collision does not mean that something is wrong with the
system. Rather, it means the forces were not of the type sufficient to
cause activation. The side air curtain system is designed to inflate in side
impact collisions, not roll-over, rear impact, frontal or near-frontal
collisions, unless the collision causes sufficient lateral deceleration.

WARNING:

Several air bag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side air

curtain has deployed,

the

air curtain will not function
again. The side air curtain
system (including the A, B and
C pillar trim and headliner)
must be inspected and serviced
by an authorized dealer.

If the

air curtain is not replaced, the
unrepaired area will increase the
risk of injury in a collision.

Seating and Safety Restraints

146

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Brand: Chevrolet Pages: 455
A-Tach 50092 Quick Start Manual preview
50092
Brand: A-Tach Pages: 2
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Brand: T-Mobile Pages: 2
Camecho R0009 Instructions preview
R0009
Brand: Camecho Pages: 2
Eibach E60-82-007-02-10 Installation Instructions preview
E60-82-007-02-10
Brand: Eibach Pages: 3
Xpresskit DBALL2-HK7 Installation Manual preview
DBALL2-HK7
Brand: Xpresskit Pages: 18
Thule 1061-1-011 Fitting Instructions preview
1061-1-011
Brand: Thule Pages: 3
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Brand: Oldsmobile Pages: 340
Ford Escape 2022 Owner'S Manual preview
Escape 2022
Brand: Ford Pages: 585
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Brand: FALCON RIDGE Pages: 6
Volvo Ski box Installation Instructions Manual preview
Ski box
Brand: Volvo Pages: 7
Ranger design 1525-NSX Quick Start Manual preview
1525-NSX
Brand: Ranger design Pages: 22
Conrad TPMS-001 Operating Instructions Manual preview
TPMS-001
Brand: Conrad Pages: 8
Jackson Racing 999-200 Installation Instructions Manual preview
999-200
Brand: Jackson Racing Pages: 14
RAM Truck 2500 2018 Supplement Manual preview
Truck 2500 2018
Brand: RAM Pages: 32
Brink 4602 Fitting Instructions Manual preview
4602
Brand: Brink Pages: 12
Mercedes-Benz SLK 2014 Owner'S Manual preview
SLK 2014
Brand: Mercedes-Benz Pages: 357

Brands by name

Popular brands

Load more brands