Mercury 2010 Milan Owner'S Manual Download Page 209 | Manualshive

Page: 209 / 330

background image

BRAKE-SHIFT INTERLOCK

This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the on position unless the brake pedal is pressed.

If you cannot move the gearshift lever out of P (Park) with ignition in
the on position and the brake pedal pressed, it is possible that a fuse has
blown or the vehicle’s brake lamps are not operating properly. Refer to

Fuses and relays

in the

Roadside Emergencies

chapter.

If the fuse is not blown and the brake lamps are working properly, the
following procedure will allow you to move the gearshift lever from P
(Park):

1. Apply the parking brake, turn the
ignition key to the off position, and
remove the key.

2. Using a screwdriver (or similar
tool), carefully pry off and remove
the chrome trim ring (1) from the
shifter base.

3. Open the storage compartment
lid and carefully pry the trim panel
(2) up from rear attachments on the
storage compartment and disconnect it from the console to expose the
inside of the gearshift.

4. Locate the brake-shift interlock
lever on the driver’s side of the
shifter assembly.

5. Apply the brake pedal. Using a
screwdriver (or similar tool), press
and hold the brake-shift interlock
lever while pulling the gearshift
lever out of the P (Park) position
and into the N (Neutral) position.

6. Install the trim panel (2) and
chrome ring (1) in reverse order.

7. Apply brake pedal, start the vehicle, and release the parking brake.

See your authorized dealer as soon as possible if this procedure
is used.

1

2

Driving

209

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
207
208
209
210
211
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: Zavoli Pages: 26

Brand: Warrior Winches Pages: 17

Brand: GATmatic Pages: 13

Dodge Charger TufBox

Brand: TUFLOC Pages: 6

Brand: Saab Pages: 445

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Webasto Pages: 18

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: SNIPER Pages: 2

Brand: BMW Pages: 392

Brand: Curt Manufacturing Pages: 4

Brand: SAFARI Pages: 5

Brand: Acura Pages: 347

Brand: Mitsubishi Pages: 490

Brand: Guardsman Pages: 2

Brand: Yakima Pages: 10

Brand: Whispbar Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands