Mercury 2010 Milan Owner'S Manual Download Page 208 | Manualshive

Page: 208 / 330

background image

WARNING:

The EPS system has diagnostics checks that

continuously monitor the EPS system to ensure proper operation

of the electronic system. When an electronic error is detected, the
message POWER STEERING ASSIST FAULT will be displayed in the
message center. If this happens, stop the vehicle in a safe place, and
turn off the engine. After at least 10 seconds, reset the system by
restarting the engine, and watch the message center for POWER
STEERING ASSIST FAULT. If the message returns, or returns while
driving, take the vehicle to your dealer to have it checked. With the
message displayed, the steering assist is turned off, making the vehicle
harder to steer.

WARNING:

If the message SERVICE POWER STEERING is

displayed in the message center, the EPS system has detected a

problem with the system function. On the next key cycle the message
SERVICE POWER STEERING NOW will be displayed and steering
assist will be removed until the steering system is serviced. Have your
vehicle taken to the nearest dealer as soon as possible.

If the steering wanders or pulls, check for:

•

an improperly inflated tire

•

uneven tire wear

•

loose or worn suspension components

•

loose or worn steering components

•

improper steering alignment

A high crown in the road or high crosswinds may also make the steering
seem to wander/pull.

Speed sensitive steering

The steering in your vehicle is speed sensitive. At lower speeds the assist
is increased to improve maneuverability.

If the amount of effort required to steer your vehicle changes while
driving at a constant vehicle speed, have the power steering system
checked by your authorized dealer.

Driving

208

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
206
207
208
209
210
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

1306 RAPID SYSTEM

Brand: Thule Pages: 8

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Honda Pages: 85

Brand: cam Pages: 28

Brand: Caltrend Pages: 3

Brand: MAcarbon Pages: 3

Brand: EUFAB Pages: 4

Brand: Yakima Pages: 28

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

Brand: Autoplugin Pages: 8

Brand: Crux Pages: 10

Brand: Nav TV Pages: 11

Brand: EUFAB Pages: 12

Brand: Chevrolet Pages: 324

Brand: Hama Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands