manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

All safety restraints in the vehicle are combination lap and shoulder
belts. All of the passenger combination lap and shoulder belts have two
types of locking modes described below:

Vehicle sensitive mode

This is the normal retractor mode, which allows free shoulder belt length
adjustment to your movements and locking in response to vehicle
movement. For example, if the driver brakes suddenly or turns a corner
sharply, or the vehicle receives an impact of approximately 5 mph
(8 km/h) or more, the combination safety belts will lock to help reduce
forward movement of the driver and passengers.

Automatic locking mode

When to use the automatic locking mode

In this mode, the shoulder belt is automatically pre-locked. The belt will
still retract to remove any slack in the shoulder belt. The automatic
locking mode is not available on the driver safety belt.

This mode should be used

any time

a child safety seat, except a

booster, is installed in passenger front or rear seating positions. Children
12 years old and under should be properly restrained in a rear seating
position whenever possible. Refer to

Safety restraints for children

or

Safety seats for children

later in this chapter.

How to use the automatic locking mode

•

Buckle the combination lap and
shoulder belt.

Seating and Safety Restraints

124

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Brand: Mazdaspeed Pages: 8
Whispbar K561W Fitting Instructions Manual preview
K561W
Brand: Whispbar Pages: 15
Lexus LX 470 Owner'S Manual preview
LX 470
Brand: Lexus Pages: 369
Mountain Top Sports Bar Installation Manual preview
Sports Bar
Brand: Mountain Top Pages: 12
TATA Motors tigor Owner'S Manual preview
tigor
Brand: TATA Motors Pages: 159
SuperATV Roof Installation Instructions Manual preview
Roof
Brand: SuperATV Pages: 7
Thule Kit 1429 Fitting Instructions Manual preview
Kit 1429
Brand: Thule Pages: 8
Kia CADENZA 2017 Features & Functions Manual preview
CADENZA 2017
Brand: Kia Pages: 58
Meritor 93000 Service Service Manual preview
93000 Service
Brand: Meritor Pages: 20
Stealthbox SB-J-GCHER2/10W3v2 Installation Manual preview
SB-J-GCHER2/10W3v2
Brand: Stealthbox Pages: 2
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Brand: Sintrones Pages: 55
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Brand: Charge Amps Pages: 14
Conrad TPMS-001 Operating Instructions Manual preview
TPMS-001
Brand: Conrad Pages: 8
Feniex QUAD QSM-8101 Manual preview
QUAD QSM-8101
Brand: Feniex Pages: 4
Hyundai TUCSON 2022 Quick Reference Manual preview
TUCSON 2022
Brand: Hyundai Pages: 32
Waeco MagicWatch MW150 Installation And Operating Manual preview
MagicWatch MW150
Brand: Waeco Pages: 144
Brodit 810698 Installation Instructions preview
810698
Brand: Brodit Pages: 2
Toyota Sienna 2000 Operating Manual preview
Sienna 2000
Brand: Toyota Pages: 277

Brands by name

Popular brands

Load more brands