Mercury 2010 Milan Owner'S Manual Download Page 267

Page: 267 / 330

ENGINE

Engines are more efficient when they are clean because grease and dirt
buildup keep the engine warmer than normal. When washing:

•

Take care when using a power washer to clean the engine. The
high-pressure fluid could penetrate the sealed parts and cause
damage.

•

Do not spray a hot engine with cold water to avoid cracking the
engine block or other engine components.

•

Spray Motorcraft

威

Engine Shampoo and Degreaser (ZC-20) on all

parts that require cleaning and pressure rinse clean. In Canada use
Motorcraft

威

Engine Shampoo (CXC-66-A).

•

Cover the highlighted areas to prevent water damage when cleaning
the engine.

•

Never wash or rinse the engine while it is running; water in the
running engine may cause internal damage.

•

Never wash or rinse any ignition coil, spark plug wire or spark plug
well, or the area in and around these locations.

2.5L ENGINE

Cleaning

267

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands

Mercury 2010 Milan, Owner'S Manual

Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands