Mercury 2010 Milan Owner'S Manual Download Page 111

Page: 111 / 330

The control is located on the outboard side of the seat cushion.

Move the control in the direction of
the arrows to raise or lower the
front portion of the seat cushion.

Move the control in the direction of
the arrows to raise or lower the rear
portion of the seat cushion.

Press the control in the direction of
the arrows to move the seat
forward, backward, up or down.

Power recline (if equipped)

Press the control to recline the
seatback forward or rearward.

Seating and Safety Restraints

111

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands

Mercury 2010 Milan, Owner'S Manual

Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands