manualshive.com logo in svg

Mercury 2010 Milan, Owner'S Manual

The Mercury 2010 Milan Owner's Manual is an essential guide for owners of this exceptional vehicle. With our user-friendly website, you can easily download this comprehensive manual for free. Get all the necessary information and instructions to make the most of your Mercury 2010 Milan at manualshive.com.

Share
Download
background image

WARNING:

When closing the moon roof, you should verify that

it is free of obstructions and ensure that children and/or pets are

not in the proximity of the moon roof opening.

To close the moon roof:

The moon roof is equipped with an automatic, one-touch, express closing
feature. Press and release the front portion of the control. To stop
motion at any time during the one-touch closing, press the control again.

Bounce-back:

When an obstacle has been detected in the moon roof opening as the
moon roof is closing, the moon roof will automatically open and stop at a
prescribed position. This is known as “bounce-back”. If the ignition is
turned off (without accessory delay being active) during bounce-back,
the moon roof will move until the bounce-back position is reached.

Bounce-back override:

To override bounce-back, press and hold the front portion of the control.
For example: Bounce-back can be used to overcome the resistance of ice
on the moon roof or seals. If during a bounce-back condition, the control
is released to the neutral position, then held in the one-touch position
within two seconds after the moon roof reaches the bounce-back
position,

the moon roof will travel with no bounce-back protection.

If the control is released before the moon roof reaches fully closed or the
ignition is turned off (without accessory delay being active), the moon
roof will stop. Security override can be used if the moon roof movement
is restricted in some way, for example, if there is ice on the moon roof or
seals.

To vent:

•

To tilt the moon roof into the vent position (when the glass panel is
closed), press and release the front portion of the control.

•

To close the moon roof from the vent position, press and hold the rear
portion of the control until the glass panel stops moving.

The moon roof has a sliding shade that can be opened or closed when
the glass panel is shut. To close the shade, pull it toward the front of the
vehicle

Accessory delay:

With accessory delay, the window switches, audio system, and moon roof
(if equipped) may be used for up to 10 minutes after the ignition switch
is turned off or until any door is opened.

Driver Controls

84

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Yakima KingJoe 2 Quick Start Manual preview
KingJoe 2
Brand: Yakima Pages: 7
Yakima BowDown Quick Start Manual preview
BowDown
Brand: Yakima Pages: 6
Yakima LOCKN'LOAD Manual preview
LOCKN'LOAD
Brand: Yakima Pages: 10
Yakima HitchSki Quick Start Manual preview
HitchSki
Brand: Yakima Pages: 12
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Brand: Genesis Pages: 3
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Brand: Mercedes-Benz Pages: 388
Standby L54 Manual preview
L54
Brand: Standby Pages: 10
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Brand: Mazdaspeed Pages: 8
Hama 00178266 Operating Instruction preview
00178266
Brand: Hama Pages: 75
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Brand: SAN HIMA Pages: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Brand: Paccar Pages: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Brand: Mercedes-Benz Pages: 153
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Brand: Mercedes-Benz Pages: 358
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Brand: walser Pages: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Brand: Mercedes-Benz Pages: 373
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Brand: Calix group Pages: 4
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Brand: BENDIX Pages: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Brand: Toyota Pages: 56

Brands by name

Popular brands

Load more brands