Mercury 2010 Milan Owner'S Manual Download Page 125 | Manualshive

Page: 125 / 330

background image

•

Grasp the shoulder portion and
pull downward until the entire
belt is pulled out.

•

Allow the belt to retract. As the belt retracts, you will hear a clicking
sound. This indicates the safety belt is now in the automatic locking
mode.

How to disengage the automatic locking mode

WARNING:

Ford Motor Company recommends that all

passenger safety belt assemblies and attaching hardware should

be inspected by an authorized dealer after any collision to verify that
the

⬙

automatic locking retractor

⬙

feature for child seats is still working

properly. Safety belt assemblies should be inspected by an authorized
dealer and must be replaced if either damage or improper operation is
noted. Failure to replace the belt and retractor assembly could
increase the risk of injury in a collision.

Unbuckle the combination lap/shoulder belt and allow it to retract
completely to disengage the automatic locking mode and activate the
vehicle sensitive (emergency) locking mode.

Safety belt height adjustment

Your vehicle has safety belt height
adjustments at the front outboard
seating positions. Adjust the height
of the shoulder belt so the belt rests
across the middle of your shoulder.

To adjust the shoulder belt height,
pull on the center button and slide
the height adjuster up or down.
Release the button and pull down
on the height adjuster to make sure
it is locked in place.

Seating and Safety Restraints

125

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
123
124
125
126
127
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Nav TV Pages: 4

Brand: BMW Pages: 38

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: Cadillac Pages: 20

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Akerstroms Tx700

Brand: LXE Pages: 146

Brand: Quadratec Pages: 14

Brand: FALCON RIDGE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands