Mercury 2010 Milan Owner'S Manual Download Page 198

Page: 198 / 330

•

Make sure the gearshift is in P
(Park).

If starting a vehicle with a manual
transmission:

•

Make sure the parking brake is
set.

•

Push the clutch pedal to the
floor.

3. Turn the key to 3 (on) without
turning the key to 4 (start).

Some warning lights will briefly illuminate. See

Warning lights and

chimes

in the

Instrument Cluster

chapter for more information

regarding the warning lights.

Driving

198

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 Milan











































































































































































































































































































































Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands

Mercury 2010 Milan, Owner'S Manual

Search results

Summary of Contents for 2010 Milan

Reviews:

Related manuals for 2010 Milan

Brands by name

Popular brands