background image

APPLICATION

Verify accessory fitment at Polaris.com.

BEFORE YOU BEGIN

Read these instructions and check to be sure all parts and tools are accounted for.
Please retain these installation instructions for future reference and parts ordering
information.

KIT CONTENTS

This kit contains parts for installation of the HomeLink

®

Kit only. Prior installation of a Battery Connection Kit is

also required (sold separately).

This Kit includes:

REF

QTY

PART DESCRIPTION

PART NUMBER

1

1

Switch Module, HomeLink

®

4016679

2

2

Harness, HomeLink

®

2413595

1

Instructions

9927141

HomeLink

®

is a registered trademark of Gentex Corporation.

TOOLS REQUIRED

• Safety Glasses
• Pliers, Push Pin
• Screwdriver Set, Torx®

• Utility Knife/Cutting Tool
• Socket Set, Metric
• Wrench Set, Metric

IMPORTANT

Your HomeLink

®

Door Opener Kit is exclusively designed for your vehicle. Please read the installation

instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your
safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

Instr 9927256

Rev 01 2016-07

Page 1 of 8

P/N 2882082

HOMELINK

®

DOOR OPENER KIT

Summary of Contents for HomeLink 2882082









Reviews: