Placing in Storage
277
Pos: 60.1 /Überschriften/Überschriften 1/A-E/Ei nlag erung @ 0\mod_1197385459120_78.docx @ 19966 @ 1 @ 1
17
Placing in Storage
Pos: 60.2 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/WARNUNG - Nichtbeachtung der grundl egenden Sicherheitshinweise alte F orm @ 254\mod_1397485793575_78.docx @ 1953347 @ @ 1
WARNING!
If the basic safety instructions are not followed, people may be seriously injured or
killed.
• To avoid accidents, the basic safety instructions in the chapter Safety must have been
read and followed, see chapter Safety "Basic safety instructions".
Pos: 60.3 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/WARNUNG - Nichtbeachtung der Sicherheitsr outinen al te For m @ 273\mod_1404117435996_78.docx @ 2058712 @ @ 1
WARNING!
If the safety routines are not adhered to, people may be seriously injured or killed.
• To avoid accidents, the safety routines in the chapter Safety must be read and followed,
see chapter Safety "Safety routines".
Pos: 60.4 /Überschriften/Überschriften 2/A-E/AAm Ende der Erntesaison @ 0\mod_1197385501276_78.docx @ 19985 @ 2 @ 1
17.1
At the End of the Harvest Season
Pos: 60.5 /BA/Einl agerung/Einl agerung_Am Ende der Erntesaison_text_R undballenpressen auß er F orti ma @ 509 \mod_1501239037823_78.docx @ 3494014 @ @ 1
Placing the machine in storage at the end of the harvest season is the best possible way to
preserve the machine.
• Park the machine in a dry spot protected from the weather and at a distance from corrosive
substances.
• Protect the tyres against external influences such as oil, grease or direct sunlight.
• Thoroughly clean the machine.
Chaff and dirt attract moisture which causes steel parts to start rusting.
ATTENTION!
Damage to the machine caused by water from a high-pressure cleaner
If the water jet from a high-pressure cleaner is aimed directly at bearings and
electrical/electronic components, these components may get damaged.
• Do not aim the water jet from a high-pressure cleaner at bearings or electrical/electronic
components.
• Lubricate the machine according to the lubrication chart. Do not wipe off any grease leaking
from the bearing positions because the ring of grease offers additional protection against
moisture.
• Grease the threads of adjusting screws and similar items.
• Clean the drive chains with a high-pressure cleaner and allow to dry.
• After cleaning and drying, moisten the drive chains with engine oil.
• Start the machine up so that the engine oil will spread on all contact surfaces.
• Check the chains and sprocket wheels for wear.
• Disassemble the PTO shaft. Lubricate the inner tubes with grease.
• Lubricate the lubricating nipples at the universal shaft and at the bearing rings of the guard
tubes, see chapter Maintenance – Lubrication, "Greasing the universal shaft".
• Lubricate the uncoated piston rods of all hydraulic cylinders liberally and insert as far as
possible.
• Wet all lever joints and bearing positions which cannot be lubricated with oil.
• Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection
agent.
• Check all moving components for smooth running. If necessary remove, clean, grease and
remount.
• If parts need to be replaced, use KRONE original spare part only.
Pos: 60.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1