manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 166

NOTICE

• Before operating the ECSS switch, be sure to stop the machine and lower the work equipment to

the ground.

• When performing inspection or maintenance, lower the work equipment to the ground first, press

ECSS switch to OFF position, then start the work.

• Keep ECSS switch turned OFF during leveling work.

ECSS switch is used to turn ECSS ON and OFF.
Position (A): ON
The pilot lamp lights up and ECSS operates.
Position (B): OFF
ECSS does not operate.

REMARK

• The  ECSS  absorbs  the  machine  vibration  during  travel

with the hydraulic spring effect of the accumulator to attain
smooth high speed travel.

• The ECSS does not operate in the 1st gear speed.
• The  ECSS  does  not  operate  while  the  boom  angle  is  25

deg. or larger from the level.

• If the travel speed exceeds 5 km/h while the gear speed is

2nd  to  4th,  ECSS  operates  automatically.If  the  travel
speed decreases below 4 km/h, ECSS stops operation au-
tomatically.

• When the bucket is empty and the work equipment is posi-

tioned  at  a  low  height,  you  may  feel  the  poor  damper
(ECSS) effect. This is not an abnormality.

FRONT WORKING LAMP SWITCH

k

k

 WARNING

The working lamps must be turned off when the machine is traveling on a public road.
 

Use the front working lamp switch to light up the front working
lamps.
Position (A): The working lamps light up.
Position (B): The working lamps go out.
When position (A) is pressed, the pilot lamp turns ON, and the
working lamps turn ON.

HAZARD LAMP SWITCH

k

k

 WARNING

When the machine is traveling normally, do not use this switch as it can mislead another vehicles.
 

EXPLANATION OF COMPONENTS

OPERATION

3-102

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands