Komatsu WA380-8 Page 7 Operation & Maintenance Manual Download | Manualshive

Page: 7 / 432

background image

SAFETY LABELS

Safety labels are affixed to the machine to inform the operator or maintenance worker on the spot when carrying
out operation or maintenance of the machine that may involve hazard.
This machine uses "Safety labels using pictograms" to indicate safety procedures.

SAFETY LABELS USING PICTOGRAMS

Safety pictograms use a picture to express a level of hazardous
condition  equivalent  to  the  signal  word.  These  safety  picto-
grams use pictures in order to let the operator or maintenance
worker understand the level and type of hazardous condition at
all times. Safety pictograms show the type of hazardous condi-
tion at the top or left side and the method of avoiding the haz-
ardous  condition  at  the  bottom  or  right  side.  In  addition,  the
type  of  hazardous  condition  is  displayed  inside  a  triangle  and
the method of avoiding the hazardous condition is shown inside
a circle.
Komatsu cannot predict every circumstance that might involve
a  potential  hazard  in  operation  and  maintenance.  Therefore,
the  safety  messages  in  this  manual  and  on  the  machine  may
not include all possible safety precautions.
If  any  procedures  or  actions  not  specifically  recommended  or
allowed in this manual are used, it is your responsibility to take
the necessary steps to ensure safety
In no event should you engage in prohibited uses or actions described in this manual.
The explanations, values, and illustrations in this manual were prepared based on the latest information availa-
ble at that time. Continuing improvements in the design of this machine can lead to changes in detail which may
not be reflected in this manual
Consult Komatsu or your Komatsu distributor for the latest available information of your machine or for ques-
tions regarding information in this manual.
The numbers in the illustrations correspond to the numbers in ( ) in the text.

FOREWORD

SAFETY LABELS

1-5

«
...
5
6
7
8
9
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: TEXIO Pages: 167

Brand: Simplicity Pages: 48

Brand: Tektite Pages: 11

Brand: Komatsu Pages: 248

Brand: Jungheinrich Pages: 103

Brand: Jungheinrich Pages: 187

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands