manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 202 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 202

REMARK

After  ENTER  switch  is  pressed  in  step  6,  the  screen
shown  in  the  figure  may  be  displayed.  This  indicates  that
the operations in steps 1 to 3 were not performed correctly
or there is trouble other than KDPF soot accumulation ab-
normality.  Check  operation  of  the  engine,  make  sure  you
are  not  depressing  the  accelerator  pedal  and  check  the
position  of  the  directional  lever  and  parking  brake  switch,
then repeat the procedure from step 5.
If  the  manual  stationary  regeneration  still  cannot  be  per-
formed,  return  to  the  standard  screen,  press  ENTER
switch  to  check  the  contents  of  other  occurring  troubles,
and take the necessary remedy.

REMARK

• The explanation of the manual stationary regeneration

is  displayed  in  3  parts  on  the  monitor  panel.  When
ENTER  switch  is  pressed,  the  regeneration  can  be
started  immediately,  regardless  of  which  part  is  dis-
played. When RETURN switch is pressed, the display
returns to the standard screen.

• If  no  monitor  switch  is  operated  for  30  seconds,  the

explanation display of the manual stationary regenera-
tion  is  not  displayed  and  the  screen  returns  to  the
standard  screen.  At  this  time,  to  display  the  explana-
tion  of  the  manual  stationary  regeneration  again,
press  ENTER  switch  on  the  standard  screen  to  dis-
play “Aftertreatment Devices Regeneration” screen.

7.

This  screen  is  displayed  during  the  manual  stationary  re-
generation. It may take more than 30 minutes to complete
the  manual  stationary  regeneration.  Do  not  touch  any
switch on the screen or accelerator pedal until the regener-
ation  is  completed  and  the  standard  screen  is  displayed
again.

EXPLANATION OF COMPONENTS

OPERATION

3-138

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments