Komatsu WA380-8 Page 188 Operation & Maintenance Manual Download

Page: 188 / 432

Pull up lever (2) of rear full-length fender (1) to unlock.

Lower lock pin (3) to unlock.

Hold handle (4) and slide rear full-length fender (1) out-
ward.

Raise lock lever (5) and turn it, then lower the lock lever at
LOCK position (L).
Rear full-length fender (1) is locked.

Pull door opening lever (6) to unlock.

Push up engine side cover (7) to open.

Pull cover (8) toward you and open it.

EXPLANATION OF COMPONENTS

OPERATION

3-124

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Related manuals for WA380-8

Brands by name

Popular brands

Komatsu WA380-8, Operation & Maintenance Manual

Search results

Summary of Contents for WA380-8

Reviews:

Related manuals for WA380-8

Brands by name

Popular brands