Komatsu WA380-8 Page 335 Operation & Maintenance Manual Download | Manualshive

Page: 335 / 432

background image

METHOD FOR CHECKING AIR CLEANER

NOTICE
The electric air cleaner clogging sensor and dust indicator are used to indicate clogging on the air
cleaner. The electric air cleaner clogging sensor indicates the cleaning timing of the air cleaner element
and the dust indicator indicates the level of clogging.
Check the dust indicator before operating the machine so that cleaning of the air cleaner element is not
required during operation.

Clean the element when the yellow piston shown in dust indica-
tor (1) display of the air cleaner entered the red (7.5 kPa) posi-
tion.
After the cleaning, press the dust indicator button to reset it.
If the yellow piston enters the red (7.5 kPa) position soon after
the cleaning, the element must be replaced.
For the element replacement procedure, see “METHOD FOR
REPLACING AIR CLEANER ELEMENT (4-18)”.

Electric air cleaner clogging sensor
Clean the air cleaner element when the yellow piston of dust in-
dicator (1) display entered the red (7.5 kPa) position or air
cleaner clogging caution lamp (2) of the machine monitor lights
up.

METHOD FOR CLEANING AIR CLEANER OUTER ELEMENT

1.

Remove clips (1) (4 pieces) and remove cover (2).

MAINTENANCE

MAINTENANCE PROCEDURE

4-15

«
...
333
334
335
336
337
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Komatsu Pages: 440

Utility WB97S-5

Brand: Komatsu Pages: 280

Brand: Parkside Pages: 99

Brand: Jungheinrich Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands