Komatsu WA380-8 Page 380 Operation & Maintenance Manual Download | Manualshive

Page: 380 / 432

background image

A: Front, B: Rear

1.

Place a container under drain plug (P) to catch the drained oil.

2.

Remove front and rear plugs (1), then remove drain plug (P) to drain the oil.

REMARK

Remove the mud and dirt from around plug (1), then remove the plug.

3.

After draining the oil, clean and install drain plug (P).

4.

Add the refill capacity of oil through plug hole (1).

REMARK

Be sure to use the only specified lubricating oil for the axle with Limited Slip Differential.

5.

Check that the oil level is proper by using level plug (1).
See “METHOD FOR CHECKING OIL LEVEL IN AXLE CASE AND ADDING OIL (4-25)”.)

REMARK

When the given work requires to use the brake more frequently than usual, replace the axle oil earlier than
the usual timing.

METHOD FOR REPLACING AIR CONDITIONER FRESH/RECIRC AIR FILTERS

Remove both the recirculation air filter and fresh air filter in the same way as in the cleaning procedure, and
replace them with new ones.
For replacement of the recirculation air filter, see “METHOD FOR CLEANING AIR CONDITIONER RECIRC AIR
FILTER (4-47)”.
For replacement of the fresh air filter, see “METHOD FOR CLEANING AIR CONDITIONER FRESH AIR FILTER
(4-42)”.

MAINTENANCE PROCEDURE

MAINTENANCE

4-60

«
...
378
379
380
381
382
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: jcb Pages: 2

Brand: Case Pages: 430

Brand: jcb Pages: 15

Brand: Takeuchi Pages: 20

CompactLine FC 150 H

Brand: Stoll Pages: 96

Brand: Ingersoll-Rand Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands