Komatsu WA380-8 Page 261 Operation & Maintenance Manual Download | Manualshive

Page: 261 / 432

background image

METHOD FOR STOPPING MACHINE

k

k

WARNING

• Avoid a sudden stop. Stop the machine gradually.
• Do not park the machine on a slope. If it is unavoida-

ble to place the machine on a slope, place the machine
at a right angle to the slope face, chock the tires, and
then lower the bucket to the ground.

• If the work equipment control levers are touched by

mistake,  the  work  equipment  may  move  suddenly
causing a serious accident. Before leaving the opera-
tor's  seat,  be  sure  to  lock  the  work  equipment  by
pressing  the  work  equipment  lock  switch  (the  pilot
lamp lights up).

• Keep depressing the brake pedal until the parking

brake pilot lamp lights up on the machine monitor
even when the parking brake switch has been turned
ON.

NOTICE
Never use the parking brake switch to brake the machine when the machine is traveling except in an
emergency.
Apply the parking brake after the machine is stopped.

1.

Release accelerator pedal (1), then depress brake pedal
(2) to stop the machine.

2.

Set directional lever (3) in NEUTRAL position (N).

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-197

«
...
259
260
261
262
263
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Jacobsen Pages: 14

Brand: Case Pages: 366

Brand: New Holland Pages: 41

Brand: Takeuchi Pages: 182

Brand: Wacker Neuson Pages: 19

Brand: Jacobsen Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands