Komatsu WA380-8 Page 348 Operation & Maintenance Manual Download | Manualshive

Page: 348 / 432

background image

METHOD FOR CLEANING FINS BY ROTATING COOLING FAN IN REVERSE

NOTICE
When rotating the fan in the reverse direction, beware extremely that dirt will not fly out and cloth, etc.
will not be wound in the fan.
Since dust may be blown up, check that there is no people around while the fan is rotating in reverse.

On the job site where the dirt sticks easily to radiator or cooler, set the automatic cooling fan to rotate the fan in
reverse. This will blow off any dirt stuck to radiator or cooler, and can extend the cleaning interval.

METHOD FOR REVERSING MANUAL OPERATION FAN

NOTICE

• Never rotate the fan in reverse by hand when performing the operation.
• Before operating the manual reverse rotation of the fan, set the engine speed to low idle.

For the manual reverse rotation of the fan, see “RADIATOR FAN MANUAL REVERSE MODE (3-63)”.

• After reverse rotation of the fan is started, set the engine speed to high idle.
• Set the high idle operation time as follows, depending on the clogging level.

Ordinary clogging: 1 to 2 minutes
Excessive clogging: 2 to 3 minutes

When the cleaning is completed, set the engine speed to low idle and restore the rotation of the fan to normal.

METHOD FOR REVERSING AUTOMATIC OPERATION FAN

For the automatic reverse rotation of the fan, see “RADIATOR FAN AUTOMATIC REVERSE MODE (3-65)”.

REMARK

• When the fan rotation direction is switched, the fan reverse pilot lamp flashes.

After a heavy load operation, the fan rotation direction may not change to protect the machine.
Set the engine speed to low idle and wait until the oil and coolant temperature goes down before operating
the switch.

• In a cold circumstance, perform the cleaning by Fan Reverse Mode within less than 5 minutes.

If the fan reverse rotation is performed for a long time, DEF hose may freeze.

METHOD FOR CLEANING FIN WITH COMPRESSED AIR

k

k

WARNING

When opening fan guard, stop the engine, and display warning tag on work equipment control lever.

METHOD FOR CLEANING FINS WITH REAR GRILLE OPENED

1.

Open rear grille (1).

MAINTENANCE PROCEDURE

MAINTENANCE

4-28

«
...
346
347
348
349
350
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Kubota Pages: 142

Brand: Scag Power Equipment Pages: 29

Brand: Doosan Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands