Komatsu WA380-8 Page 356 Operation & Maintenance Manual Download | Manualshive

Page: 356 / 432

background image

SELECT AND CHECK TIRES

k

k

WARNING

If a tire or a rim is handled improperly, the tire may burst or
may be damaged and the rim may be broken and scat-
tered, and that can cause serious injury or death.

• Since maintenance, disassembly, repair and assembly of

the tires and rims require special equipment and skill, be
sure to ask a tire repair shop to do the work.

• Never perform welding or light a fire near the tire.

TIRE SELECTION

k

k

WARNING

Select the tires according to the conditions of use and the weight of the attachments on the machine.
Use only specified tires and inflate them to the specified pressure.

Select the tires according to the conditions of use and the weight of the attachments of the machine.
Use the tires shown in the following table.
The travel speed displayed varies with the tire size.

NOTICE
For usability of tires, consult your Komatsu distributor.

• Do not install the tire protector (mesh chain) to rear wheels.
• Do not to use tires, such as urethane tires, that weigh remarkably more than the standard tires

since the machine can be damaged due to an unexpected load.

• If a tire not specified by Komatsu is used, rim displacement between the tire and rim may occur.

Operator comfort, as well, may be degraded.

Tire size

Standard

Front tire: 23.5R25

☆

Rear tire: 23.5R25

☆

Optional

Front tire: 23.5-25-16PR

Rear tire: 23.5-25-16PR

MAINTENANCE PROCEDURE

MAINTENANCE

4-36

«
...
354
355
356
357
358
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Case Pages: 41

Brand: Parkside Pages: 43

Brand: Hitachi Pages: 278

Brand: AEM Pages: 528

PalletPal Stack-n-Go FPS3000-43 NAS

Brand: Southworth Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands