manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual

The Komatsu WA380-8 Operation & Maintenance Manual is a comprehensive guide that provides detailed instructions for the safe operation and routine maintenance of the WA380-8 model. This manual is available for free download at manualshive.com, ensuring easy access to essential information for maximizing the performance and lifespan of your Komatsu equipment.

Share
Download
background image

SCR INFORMATION

Each item in “SCR Information” menu (D) is for displaying infor-
mation related to SCR and DEF.
For  details  of  “SCR  Information”,  see  “HANDLE  UREA  SCR
SYSTEM WARNING (3-142)”.

MAINTENANCE SCREEN SETTING

Each  item  on  “Maintenance”  menu  screen  (E)  is  used  for  dis-
playing and setting the notification relevant to maintenance.
On the “Maintenance” menu screen, the following maintenance
items, their replacement intervals, and their remaining times to
the next replacement are displayed.

Maintenance item

Interval ( h)

(Default)

Air Cleaner Cleaning or Change

-

Coolant Change

-

Fuel Prefilter Change

500

Engine Oil Change

500

Engine Oil Filter Change

500

T/M Oil Filter Change

1000

Fuel Main Filter Change

1000

T/M Oil Change

1000

Axle Oil Change

2000

Hydraulic Oil Change

2000

Hydraulic Oil Filter Change

2000

Hyd Oil Tank Breather Change

2000

KCCV Filter Change

2000

DEF Filter Change

2000

DEF Tank Breather Change

2000

KDPF Filter Cleaning

4500

DEF Tank Washing

4500

OPERATION

EXPLANATION OF COMPONENTS

3-75

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

IHI 17VX3 Service Manual preview
17VX3
Brand: IHI Pages: 130
Komatsu Utility F50003 Operation & Maintenance Manual preview
F50003
Brand: Komatsu Utility Pages: 284
Kioti CK35 Series Operator'S Manual preview
CK35 Series
Brand: Kioti Pages: 25
Volvo MC60 Service Information preview
MC60
Brand: Volvo Pages: 7
Shini SAL-430 Instruction Manual preview
SAL-430
Brand: Shini Pages: 29
Shini SAL-700G Series Manual preview
SAL-700G Series
Brand: Shini Pages: 34
Azbil SLP-C4A User Manual preview
SLP-C4A
Brand: Azbil Pages: 56

Brands by name

Popular brands

Load more brands