Komatsu WA380-8 Page 372 Operation & Maintenance Manual Download | Manualshive

Page: 372 / 432

background image

EVERY 1000 HOURS MAINTENANCE

Maintenance for every 50, 100, 250 and 500 hours service should be performed at the same time.

METHOD FOR REPLACING FUEL MAIN FILTER CARTRIDGE

k

k

WARNING

• Immediately after the engine is stopped, the parts are still very hot. Do not replace the filter immedi-

ately. Wait for all of parts to cool down before starting the work.

• High pressure is generated inside the engine fuel piping system when the engine is running.

When replacing the filter, wait for at least 30 seconds after stopping the engine to let the internal
pressure go down before replacing the filter.

• Do not bring any open flame close.

NOTICE

• Komatsu genuine fuel filter cartridges use a special filter that has highly efficient filtering ability.

When replacing parts, Komatsu recommends using Komatsu genuine parts.

• The common rail fuel injection system used on this machine consists of more precise parts than

those in the conventional injection pump and nozzles. If any cartridge other than a Komatsu genu-
ine filter cartridge is used, dust or dirt may get in and cause problems with the injection system.
Never use a substitute.

• When performing inspection and maintenance of the fuel system, be careful not to let any foreign

material get in, more than ever before. If dust sticks to the fuel system, wash it off thoroughly with
fuel.

• After removing the filter cartridge, fuel drops fall down from the filter head.

In order to prevent outflow of the fuel, be sure not to leave the machine while the filter cartridge is
being removed.

Items to be prepared

• Container to catch the drained fuel
• Filter wrench

After replacing the fuel prefilter cartridge, replace the fuel main filter cartridge.
1.

Open the engine side cover on the right side of the ma-
chine.

2.

Place a container under the filter cartridge to catch the
fuel.

3.

Turn filter cartridge (1) counterclockwise by using the filter
wrench, and remove it.

4.

Clean the filter head.
Replace inner seal (2) with a new one.

MAINTENANCE PROCEDURE

MAINTENANCE

4-52

«
...
370
371
372
373
374
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Case Pages: 41

Brand: Pitney Bowes Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands