Komatsu WA380-8 Page 406 Operation & Maintenance Manual Download | Manualshive

Page: 406 / 432

background image

You can select FORWARD, NEUTRAL, or REVERSE with the
multi-function mono-lever directional selector switch.
The basic operation is as follows.
Position (F): FORWARD
Position (N): NEUTRAL
Position (R): REVERSE

Before using this switch to change the travel direction, set the
directional lever to NEUTRAL position and set directional se-
lector enable switch (A) of R.H. switch panel to position (a).

PCS(PROPORTIONAL CONTROL SWITCH)

PCS (Proportional Control Switch) is used to operate the third
attachment.
The hydraulic oil discharged by the switch operation is in pro-
portion to the stroke of the switch.
The switch has 2 control modes; continuous mode and propor-
tional mode.
You can set the maximum flow when the switch is operated and
change the control mode on the monitor.
Position (A): RETRACT
Position (B): NEUTRAL
However, when switch is operated to limit of position (C) to enable the detent control in the continuous mode,
this position is for HOLD.
Position (C): EXTEND

HANDLE MULTIFUNCTION MONO-LEVER

ATTACHMENTS AND OPTIONS

6-6

«
...
404
405
406
407
408
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Doosan Pages: 21

Brand: Barko Pages: 99

Brand: Toro Pages: 12

Brand: Toro Pages: 28

Brand: Gehl Pages: 92

Brand: Gehl Pages: 88

Brand: Gehl Pages: 192

Turboloader H360

Brand: Gianni Ferrari Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands