Komatsu WA380-8 Page 338 Operation & Maintenance Manual Download

Page: 338 / 432

11. Push the button of dust indicator.

The yellow piston returns.

Even though the outer element has not been cleaned up to 6 times, if the yellow piston of dust indicator laps
over the red zone (7.5 kPa {0.08 kg/cm

}) soon after the cleaning, or if the air cleaner clogging caution lamp

lights up, replace both the inner and outer elements.

METHOD FOR REPLACING AIR CLEANER ELEMENT

Remove clips (1) (4 pieces) and remove cover (2).

Install on-board air cleaner pull-out jig (3) to the narrow
part of outer element (4).

MAINTENANCE PROCEDURE

MAINTENANCE

4-18

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Related manuals for WA380-8

Brands by name

Popular brands

Komatsu WA380-8, Operation & Maintenance Manual

Search results

Summary of Contents for WA380-8

Reviews:

Related manuals for WA380-8

Brands by name

Popular brands