Komatsu WA380-8 Page 246 Operation & Maintenance Manual Download | Manualshive

Page: 246 / 432

background image

METHOD FOR ADJUSTING LEVER STAND IN FORE-AND-AFT DIRECTION

While pulling lever (3) up with the left hand, hold armrest (1)
with the right hand to move forward or backward, and then re-
lease lever (3).
Adjustment amount: 180 mm

METHOD FOR OPERATIONS AND CHECKS BEFORE STARTING ENGINE

k

k

WARNING

When starting the engine, check that the work equipment is securely locked (the pilot lamp in the switch
lights up).
If the work equipment control levers are not locked and they are touched by accident when starting the
engine, the work equipment may move unexpectedly, and this may lead to a serious injury or death.

Perform the check before starting the engine according to the following procedure.
1.

Check that battery disconnect switch (S) is in ON position
(I).

2.

Check that parking brake switch (1) is in ON position (A).

3.

Check that directional lever (2) is in NEUTRAL position
(N).

REMARK

The engine can be started only when the directional lever
is in NEUTRAL position (N).

4.

Check that the bucket is lowered to the ground.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-182

«
...
244
245
246
247
248
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Jacobsen Pages: 14

Brand: Wacker Neuson Pages: 254

Brand: Barreto Pages: 22

Brand: Toro Pages: 20

Brand: Toro Pages: 554

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands