Home
/
Komatsu
/
WA380-8
/
Operation & Maintenance Manual

Komatsu WA380-8, Operation & Maintenance Manual, Page: 240 / 432

Share

Page: 240 / 432

Komatsu WA380-8 Operation & Maintenance Manual Download Page 240

METHOD FOR REMOVING AND INSTALLING HEADREST
METHOD FOR REMOVING HEADREST

When the headrest is not necessary, remove it according to the following procedure.
1.

Pull up the headrest until it stops.

2.

Pull up the headrest strongly, and it will come out.

METHOD FOR INSTALLING HEADREST

1.

Insert the headrest into the hole at the seat back.

2.

Push down the headrest.

METHOD FOR ADJUSTING MIRRORS

k

k

WARNING

• Be sure to adjust the mirrors before starting work. If they are not adjusted properly, you cannot se-

cure the visibility and may be injured or may lead to a serious personal injury or death.

• The tightening torque for the mirror mounting bolts is set at an optimum value.

If it is loosened by unexpected contacts, ask your Komatsu distributor for adjustment.

Mirrors A, B
Adjust the mirror to a position which gives the best view from
the operator's seat of the blind spot at the right and left sides at
the rear of the machine.
Adjust the mirror angle so that you can see a person who is
standing at the right or left rear end position of the machine (or
an object having the diameter of approximately 30 cm and the
height of approximately 1 m).

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-176

«
...
238
239
240
241
242
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments