Komatsu WA380-8 Page 244 Operation & Maintenance Manual Download | Manualshive

Page: 244 / 432

background image

CHECK REAR VIEW CAMERA GUIDE LINE

Check that the images on the rear view camera monitor are
normal as shown in the figure. Then confirm that machine width
reference line (D) matches to tire outside width (B), and hori-
zontal line (E) matches to position (C) that is 1.5 m away from
the rear end of the machine.
When the reference line is abnormal, change its setting to Non-
display and contact your Komatsu distributor.

METHOD FOR FASTENING AND UNFASTENING SEAT BELT

k

k

WARNING

• Before fastening the seat belt, check that there is no problem in the belt mounting bracket or belt. If

it is worn or damaged, replace it.

• Even if no problem can be seen in the belt, replace the seat belt every 3 years from starting usage

or 5 years after manufacture whichever comes sooner. The date of manufacture of the belt is shown
on the back of the belt.

• Before operating, fasten the seatbelt.
• Be sure to use the seat belt during operation.
• Do not twist the seat belt when fastening.

REMARK

The date indicated on the seat belt is the manufactured date. It is the start of the 5-year period. It is not the start
of the 3-year period of actual usage.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-180

«
...
242
243
244
245
246
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Kato Imer Pages: 120

Drexel SLT30 AC

Brand: Landoll Pages: 82

Brand: Gehl Pages: 82

Brand: Gehl Pages: 112

Brand: Gehl Pages: 170

Brand: Gehl Pages: 206

Brand: Gehl Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands