Komatsu WA380-8 Page 376 Operation & Maintenance Manual Download | Manualshive

Page: 376 / 432

background image

METHOD FOR CHECKING AND REPLACING ALTERNATOR BELT

• Special tools are required for the replacement of the belt. Ask your Komatsu distributor to perform this work.
• Since the auto-tensioner is installed, tension adjustment is not required.

If alternator drive belt shows the following conditions, it must be
replaced. Ask your Komatsu distributor to replace it.

• When vertical flaw (2) that crosses horizontal flaw (1) is

found.

• When a part of the belt has tears (3).
• You do not need to replace the belt when it has only hori-

zontal flaw (4).

EVERY 2000 HOURS MAINTENANCE

Maintenance for every 50, 100, 250, 500, and 1000 hours service should be performed at the same time.

METHOD FOR CHANGING OIL IN HYDRAULIC TANK, CLEANING HYDRAULIC
TANK STRAINER

k

k

WARNING

• Immediately after the engine is stopped, its parts and oil are still very hot and may cause burn in-

jury. Wait for the temperature to go down, and then start the work.

• When removing the oil filler cap, the oil may spout out. Turn it slowly to release the internal pres-

sure, then remove it carefully.

Refill capacity : 142 ℓ
Items to be prepared

• Container to catch drained oil

1.

Remove inspection window (1) of the undercover.

2.

Lower the bucket to the ground with its bottom level, apply
the parking brake, then stop the engine.

3.

Loosen the bolts and remove cover (2).

MAINTENANCE PROCEDURE

MAINTENANCE

4-56

«
...
374
375
376
377
378
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Simplicity Pages: 12

Brand: Worldwide Construction And Forestry Division Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands