Komatsu WA380-8 Page 190 Operation & Maintenance Manual Download | Manualshive

Page: 190 / 432

background image

This is installed to the right inside of the operator's cab.
The directions are described on the nameplate affixed to the
fire extinguisher. Carefully read and understand them before-
hand for emergencies.

BATTERY DISCONNECT SWITCH

k

k

CAUTION

• Do not operate the battery disconnect switch while the engine is running.

The large current generated by the alternator may burn the electric parts and cause a fire.
Operate the battery disconnect switch only when the engine is stopped.

• If the battery disconnect switch is turned to OFF position, always remove the switch key.

If someone turns the key to ON position carelessly, this is extremely dangerous.

NOTICE

• Keep battery disconnect switch in ON position except the following cases.

• When the machine is stored for a long time (more than a month)
• When repairing the electrical system
• When performing electric welding
• When handling the battery
• When replacing the fuse, etc.

• Do not turn the battery disconnect switch to OFF position while the system operating lamp is lit. If

the battery disconnect switch is turned off while this lamp is lit, the data in the controller may be
lost.

• If this switch is turned to OFF position, all the electrical system is cut out and the functions of KOM-

TRAX stop. In addition, the time setting of the clock may be lost. In this case, set the information
again. For detail, see “CLOCK ADJUSTMENT (3-82)”.

EXPLANATION OF COMPONENTS

OPERATION

3-126

«
...
188
189
190
191
192
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Genie Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands