Komatsu WA380-8 Page 266 Operation & Maintenance Manual Download | Manualshive

Page: 266 / 432

background image

Steering oil pressure caution lamp (red) (1) and secondary
steering pilot lamp (green) (2) light up simultaneously.
If the steering oil pressure caution lamp (red) or the secondary
steering pilot lamp (green) does not light up, it is abnormal.
Ask your Komatsu distributor for inspection.

k

k

CAUTION

If the machine is steered during self-check, it may move.
Do not steer the machine during self-check.

Check of the secondary steering is not performed in the following cases.

• When you have turned the starting switch to ON position and, without starting the engine, turned it to OFF

position then turned it to ON position again

• When you have turned the starting switch to ON position again immediately after the engine is stopped

when the steering pressure is not completely lowered

• When the engine preheating is operated

To check the secondary steering function, press the secondary steering switch after the warm-up operation.

HANDLE TORQUE CONVERTER LOCKUP

When turning the starting switch of this machine to ON position, the lockup mode is turned on.
When changing the setting, see “LOCKUP FUNCTION SETTING WHEN KEY IS ON (3-73)”.

k

k

WARNING

While traveling a downhill (A) of 6 ° or steeper, do not de-
press the accelerator pedal to the stroke end regardless of
ON or OFF of the torque converter lockup function mode.
Otherwise, accidents can be caused by an excessive
speed.

NOTICE
During the high-speed travels listed below, do not shift
down the gear speed in order to prevent overrun.
(The travel speed specified in this section may vary de-
pending on the conditions of use or on road surface condi-
tion.)

• Do not shift down to F2 while the machine is traveling

at 18 km/h or faster in F3.

• Do not shift down to F3 while the machine is traveling

at 28 km/h or faster in F4.

When the actual gear speed is in the rang of 2nd to 4th in both the forward and reverse, the torque converter
lockup function is activated corresponding to the actual travel speed and type of operation to shift the transmis-
sion to the direct drive.
In order to prevent overrun, the lockup is automatically canceled if engine speed reaches 2500 rpm or above in
each gear speed.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-202

«
...
264
265
266
267
268
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Super Boom L150

Brand: New Holland Pages: 1

Super Boom C175

Brand: New Holland Pages: 1

Brand: New Holland Pages: 7

Brand: New Holland Pages: 8

Brand: New Holland Pages: 41

Brand: jcb Pages: 51

Brand: Thomas Pages: 70

Brand: Thomas Pages: 132

Brand: Toro Pages: 4

Brand: Toro Pages: 48

MAGNUM SIGNATURE SERIES

Brand: Norfield Pages: 6

Brand: ahlmann Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands