Komatsu WA380-8 Page 159 Operation & Maintenance Manual Download | Manualshive

Page: 159 / 432

background image

(3) Engine shutdown secondary switch
(4) Gear speed switch
(5) Hazard lamp switch
(6) Horn switch
(7) Lamp switch
(7) Turn signal lever
(7) Dimmer switch
(8) Parking brake switch
(9) Rear view monitor brightness adjustment switch
(10) Work equipment lock switch
(11) Kickdown switch
(12) Hold switch
(13) Cigarette lighter
(14) Starting switch
(15) Front wiper switch
(16) Rear wiper switch
(17) Monitor brightness selector switch

(18) Beacon lamp switch (if equipped)
(19) Auto-greasing switch
(20) Rear working lamp switch
(21) Rear heated wire glass switch
(22) Room lamp switch
(23) Directional selector switch (if equipped)
(24) Transmission cut-off switch
(24) Transmission cut-off set switch
(25) Power mode selector switch
(26) Transmission shift mode selector switch
(27) Torque converter lockup switch
(28) Directional selector enable switch on R.H. switch

panel (if equipped)

(29) Remote positioner switch
(30) Auto-digging switch
(31) Secondary steering switch
(32) Quick coupler switch (if equipped)

STARTING SWITCH

Starting switch is used to start or stop the engine.

(A): OFF position

The key can be removed from the starting switch, the electrical
current to the electrical system is cut, and the engine stops. In
addition, the parking brake is applied automatically.

(B): ON position

Electric current flows through the charging and lamp circuits.
Keep the switch at this position while the engine is running.
When the ambient temperature is low during engine startup,
the engine preheating pilot lamp lights up and engine preheat-
ing starts automatically.
This preheating time depends on the ambient temperature during engine startup.
When the engine preheating pilot lamp lights up, wait for a while. When it goes out, then turn the starting key to
the START position.

(C): START position

This is the position to start the engine. Hold the key at this position while cranking the engine. Release your
hand off the key immediately after the engine has been started. The key returns to ON position (B).

(D): Manual preheat position

In cold weather, you can increase the engine preheating time longer than the automatic preheating time. To in-
crease it, turn the starting switch key to this position.
When you release your hand, the switch returns to position (A). Immediately turn the key to position (C) and
start the engine.

OPERATION

EXPLANATION OF COMPONENTS

3-95

«
...
157
158
159
160
161
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Simplicity Pages: 12

Brand: Genie Pages: 64

Brand: Land Pride Pages: 34

Brand: Messersi Pages: 34

Brand: Terramite Pages: 112

Brand: Azbil Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands