Komatsu WA380-8 Page 161 Operation & Maintenance Manual Download | Manualshive

Page: 161 / 432

background image

HORN SWITCH

If you press the horn switch, the horn sounds.

KICKDOWN SWITCH

The kickdown switch is located at the top of the boom control
lever.
In the manual shift mode, each time the kickdown switch is
pressed while the machine is traveling in forward 2nd (F2) , the
gear speed is shiftted down to forward 1st (F1).
Use this switch to increase the rim pull during scooping.
While the shift range is in forward 1st (F1) in E mode, the work-
ing mode can be changed to P mode by pressing the kickdown
switch.
Use this switch to increase the rim pull further during scooping
or for scrape-up work.

In E mode

2nd

E mode

→

1st

E mode

→

1st

P mode

In P mode

2nd

P mode

→

1st

P mode

In the auto-shift mode, if the travel speed is 10.5 km/h or slower, the kickdown switch operates and the gear
speed can be shifted down to 1st from any gear speed of the forward or reverse travel.
This function facilitates the load-and-carry operation.
When the travel speed is higher than 10.5 km/h, the gear speed is shifted down by one gear speed each time
the kickdown switch is pressed in the order F4, F3, and F2.

OPERATION

EXPLANATION OF COMPONENTS

3-97

«
...
159
160
161
162
163
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

PalletPal Spring

Brand: Southworth Pages: 16

TELPRO PANELLIFT 195 T

Brand: Paragon Pro Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands