manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 215 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 215

power  derate.  This  engine  power  restoration  works  only  when  the  Inducement  status  is  “Severe  Induce-
ment” and relieves back temporarily to the power deration of “Low level Inducement”. The operator can re-
store engine power through the machine monitor. For the engine power restoration procedure, refer to the
section of “Temporary Restoration from Inducement” in this manual. If Inducement advances to “Severe In-
ducement” and it becomes necessary to restore engine power, use the engine power restoration function to
move the machine to a safe place and contact your Komatsu distributor.

Inducement strategy when abnormality is found in the EGR Valve System by the
Urea SCR system

If any abnormality is detected in the EGR Valve System through the Urea SCR system, the Inducement strategy
is activated.
The  inducement  strategy  progresses  in  4  levels,  “Warning”,
“Continuous Warning”, “Low level Inducement”, and “Severe In-
ducement”.  The  Inducement  strategy  includes  visual  alert  by
the Engine system caution lamp (1), DEF system caution lamp
(2), and Action Level displayed on the machine monitor (3), au-
dible alert by a buzzer and stepwise engine power deration that
advances to speed limitation to low idle. Engine power deration
starts  with  Action  Level  “L03  (Warning,  Continuous  Warning
and  Low  level  Inducement)”  and  advances  to  further  deration
when  “L04  (Severe  Inducement)”  is  displayed.  Once  the  sys-
tem  advances  to  “Severe  Inducement”,  the  engine  power  will
be further derated. If “L03” is displayed, move the machine to a
safe place and contact your Komatsu distributor.
The content of the warning can be checked on the “SCR Information” screen of the user menu.
Perform the following procedure.
Press  the  menu  switch  to  display  the  “SCR  Information”
screen.
After a lapse of 3 seconds to stop the machine, “SCR Informa-
tion” screen is displayed.

“SCR  Information”  screen  displays  remaining  time  to  the  next
Inducement  status  in  the  column  (6),  and  information  on  the
Urea  SCR  System  condition  (4),  and  the  current  status  of  In-
ducement (5).

OPERATION

EXPLANATION OF COMPONENTS

3-151

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments