Komatsu WA380-8 Page 48 Operation & Maintenance Manual Download | Manualshive

Page: 48 / 432

background image

• If you drive the machine at high speed continuously for a long time, the tires will overheat and the internal

pressure will become abnormally high. This may cause the tires to burst. If a tire bursts, it produces a large
destructive force, and this may cause serious injury or death.

• Directional lever or directional selector switch (if equipped) must not be set to NEUTRAL position (N) while

traveling or traveling downhill. Set the direction of directional lever or directional selector switch (if equip-
ped) in the traveling direction of the machine.

• It is dangerous that the engine brake is disabled and the steering wheel becomes heavier.
• The transmission and other parts of the power train may be damaged, and it may cause serious per-

sonal injury or death.

PRECAUTIONS WHEN TRAVELING ON SLOPES

To prevent the machine from tipping over or slipping to the side, always observe the following.

• Keep the work equipment at height (A) of approximately 20

to 30 cm above the ground. In case of emergency, lower
the work equipment to the ground immediately to help
stopping the machine.

• Always drive the machine straight up or down a slope.

Driving the machine at an angle or across the slope is ex-
tremely dangerous.

• Do not turn on slopes or drive across slopes. Always go

down to a flat place to change the position of the machine,
then drive it on to the slope again.

• Drive the machine at low speed on the grass or fallen leaves. Even with slight slopes, there is a hazard that

the machine may slip.

• If the engine should stop on a slope, depress the brake pedal immediately, lower the bucket and apply the

parking brake to stop the machine.

• When traveling downhill, never shift gear or place the transmission at neutral.

Engine brake does not work and dangerous. The direction of directional lever or directional selector switch
(if equipped) must be set in the traveling direction of the machine.

• When driving the machine downhill, drive it slowly at low speed. Depress the brake pedal or use the engine

brake as necessary.

PRECAUTIONS FOR OPERATION

SAFETY

2-28

«
...
46
47
48
49
50
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands