Komatsu WA380-8 Page 140 Operation & Maintenance Manual Download | Manualshive

Page: 140 / 432

background image

When  the  time  remaining  to  the  next  “Maintenance”  for  any
item is less than the maintenance notice time (initial setting: 30
hours), the remaining time display (1) is highlighted in yellow.
When  the  time  remaining  to  the  maintenance  becomes  0
hours, the Remain (1) is highlighted in red. The time after the
replacement interval is indicated with the negative symbol.
If  any  item  is  displayed  in  red,  perform  the  maintenance  for  it
immediately.

REMARK

The replacement intervals in “Air Cleaner Cleaning or Change”
and “Coolant Change” are not set initially.
If you want to change the setting for the maintenance interval
and the maintenance notice time, consult your Komatsu distrib-
utor.
When the maintenance time caution lamp (2) is lit on the stand-
ard screen, press the menu switch, and the screen automati-
cally displays the “Maintenance” menu screen (E).

METHOD FOR RESETING REMAINING TIME FOR MAINTENANCE

After performing maintenance, reset the remaining time for maintenance according to the following procedure.
1.

On “Maintenance” menu screen, select an item to reset the
remaining time, then keep pressing ENTER switch (1) for
more than 1.5 seconds.

REMARK

If ENTER switch (1) is not pressed for enough time, the
switch operating sound can be heard, but the screen does
not switch to the screen for resetting the remaining time for
maintenance.

EXPLANATION OF COMPONENTS

OPERATION

3-76

«
...
138
139
140
141
142
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Case Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands