Komatsu WA380-8 Page 383 Operation & Maintenance Manual Download | Manualshive

Page: 383 / 432

background image

Items to be prepared

• Container to catch drained oil
• Special wrench for KCCV

The KCCV ventilator is located in the positions shown in the
figure.

For the use of the special wrench, see the figure.

1.

By using the special wrench, loosen ring (3) of KCCV ven-
tilator (1).

2.

After ring (3) comes off, remove case (4) from body (2) and remove element (5).
There may be oil accumulated or sticking in the case and
element. Take care not to spill the oil when replacing the
element.

REMARK

When the ambient temperature is low, water or emulsified
matter may stick to the inside of KCCV because of con-
densation of water vapor in the blowby gas. However, if
the coolant level is normal, it is not a problem.

3.

Remove used O-ring (6) sticking to case (4) and install a new O-ring contained in the service kit.

MAINTENANCE

MAINTENANCE PROCEDURE

4-63

«
...
381
382
383
384
385
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Toro Pages: 40

Brand: jcb Pages: 51

Brand: AEM Pages: 528

Brand: Vermeer Pages: 104

Brand: Terex Pages: 218

Brand: Gehl Pages: 92

Brand: Gehl Pages: 88

Brand: Gehl Pages: 192

Brand: Gravely Pages: 34

Brand: diamond mowers Pages: 40

Brand: Azbil Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands