Komatsu WA380-8 Page 319 Operation & Maintenance Manual Download

Page: 319 / 432

Problem

Main causes

Remedy

Indicator of engine coolant tempera-
ture gauge does not rise up to the
green range

Defective thermostat

Replace thermostat. (*)

Defective coolant temperature gauge

Replace coolant temperature gauge.
(*)

Defective monitor

Replace. (*)

Starting motor turns but engine does
not start.

Lack of fuel

Add fuel. See CHECKS BEFORE
STARTING.

Air in fuel system

Repair portion where air is sucked in.

Fuel filter is not filled with fuel.

Fill filter with fuel. See EVERY 500
HOURS MAINTENANCE.

Defective fuel injection pump or injec-
tor

Replace pump or injector. (*)

Starting motor turns engine sluggish-
ly.

See PHENOMENA AND ACTIONS
FOR ELECTRICAL SYSTEM.

Starting motor does not turn.

See PHENOMENA AND ACTIONS
FOR ELECTRICAL SYSTEM.

Preheating caution lamp does not
light up.

See PHENOMENA AND ACTIONS
FOR ELECTRICAL SYSTEM.

Incorrect valve clearance
(Defective compression)

Adjust valve clearance. (*)

Exhaust gas color is white or bluish.

Water entry in the aftertreatment de-
vices

Check, repair. (*)

Breakage of the aftertreatment devi-
ces

Replace the aftertreatment devices.
(*)

Excessive oil in oil pan

Set oil to specified level. See
CHECKS BEFORE STARTING.

Improper fuel

Replace with specified fuel.

Exhaust gas turns black from time to
time.

Breakage of the aftertreatment devi-
ces

Replace the aftertreatment devices.
(*)

Clogged air cleaner element

Clean or replace. See WHEN RE-
QUIRED.

Defective injector

Replace injector. (*)

Defective compression

See the above section on defective
compression. (*)

Defective turbocharger

Check, replace turbocharger. (*)

Combustion makes breathing sound
from time to time.

Defective nozzle

Replace nozzle. (*)

Abnormal noise is generated.
(Combustion or mechanical)

Low grade fuel being used

Replace with specified fuel.

Overheating

Refer to "Indicator of engine coolant
temperature gauge is in red range"
as above.

Breakage of inside of the aftertreat-
ment devices

Replace the aftertreatment devices.
(*)

Excessive valve clearance

Adjust clearance. (*)

DEF level caution lamp lights up.

Lowering of DEF level

Add DEF.

OPERATION

TROUBLES AND ACTIONS

3-255

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Related manuals for WA380-8

Brands by name

Popular brands

Komatsu WA380-8, Operation & Maintenance Manual

Search results

Summary of Contents for WA380-8

Reviews:

Related manuals for WA380-8

Brands by name

Popular brands