Komatsu WA380-8 Page 359 Operation & Maintenance Manual Download | Manualshive

Page: 359 / 432

background image

1.

Install rear full-length fender (1).
For the opening method of the rear full-length fender, see
“METHOD FOR OPENING REAR FULL-LENGTH FEND-
ER AND ENGINE SIDE COVER (3-123)”.

2.

By using a grease pump, pump in grease through grease
fittings (2).

REMARK

There are 4 grease fittings per one hinge.

3.

After greasing, repeat open and close several times for the
grease to fit completely.

CHECKING AUTO-GREASING AND OPERATION METHOD FOR FILLING
GREASE

NOTICE

• Fill in only clean lubricant by using a suitable tool (A

or B).
Soiled lubricant leads to serious system trouble.

• If the grease tank is emptied below “MIN” mark, the air

bleeding of whole system must be performed.
To bleed air from the auto-greasing system, consult
your Komatsu distributor.

Maintenance work should be performed if needed or every 50
hours.
If any problem occurs, consult your Komatsu distributor.
Prepare the grease.
For the types of grease, see “METHOD FOR USING FUEL,
COOLANT AND LUBRICANTS ACCORDING TO AMBIENT
TEMPERATURE (7-6)”.

MAINTENANCE

MAINTENANCE PROCEDURE

4-39

«
...
357
358
359
360
361
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: BARKO LOADERS Pages: 112

Brand: Toro Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands