-
32
1 Aperture
1 Aperture
Faults in rim cleaner
Fault
Possible cause
Remedy
By whom
Inadequate or no
flow of water/de-
tergent
Orifice plate in the hub clogged.
Clean the parts.
Operator, Cus-
tomer Service
Faults in the compressor
Fault
Possible cause
Remedy
By whom
Compressor
switches on and
off frequently.
Condensate level in pressure container too
high.
Drain the condensate from the pressure contain-
er of the compressor.
Operator/Cus-
tomer Service
Fault in the foam production (option)
Fault
Possible cause
Remedy
of whom
Bad dry foam
quality, foam too
dry or too wet
Detergent container is empty
Replace the container.
Operator
Suction filter in the detergent
tank is dirty.
Rinse the filter with warm water
Operator
Water supply is too low
Re-establish water supply, check the settings of the pressure
reducer for water (0.5 MPa (5 bar))
Operator
Compressor does not supply air Check the compressor
Drain the condensate from the pressure container of the com-
pressor.
Customer Ser-
vice
Compressor overheated
After cooling off, the compressor will automatically start oper-
ating again.
Operator
Pressure reducer foam station
contaminated
Clean pressure reducer
Operator
Solenoid valve water/chemicals
does not open
Check the voltage using a magnetic field tester, clean sole-
noid valve, replace if required
Operator, Cus-
tomer Service
Settings of the pressure reduc-
er for water or air incorrect
Setting of the detergent dosage
incorrect
Perform basic setup (see chapter B Operation and Settings)
Customer Ser-
vice
incorrect detergent, detergent
contaminated or old
Replace detergent
Operator
Inadequate or no
flow of water/de-
tergent
Orifice plate in the hub clogged. Clean the parts.
Operator, Cus-
tomer Service
70
EN
Summary of Contents for SB MU
