-
25
The bases of a safe operating of the equip-
ment is thr regularly maintenance accord-
ing to the following maintenance plan.
Use only original parts of the manufacturer
or part suggessted by him, such as
–
parts and wearing parts,
–
accessories parts,
–
operating materials,
–
cleaning agents.
Danger
Risk of accident while working on the unit.
During all tasks
Turn off the water supply; close the
fresh water tap,
First switch-on in voltage-less state,
switch off the emergency stop switch in
the building and secure it against being
switched on again.
–
Operator
Work designated with the sign “Opera-
tor” may only be carried out by persons
who have been instructed in the safe
operation and maintenance on the
washing system.
–
Electricians
Persons with a professional training in
the electro-technical area.
–
Customer Service
Only KÄRCHER service engineers are
allowed to carry out work with the note
“Customer Service”.
1 Fault indicator in the display of the con-
trol
Troubleshooting
Who may remedy faults?
Fault indication
Troubleshooting in Switching Cabinet
Faults shown in the display
Display
Cause
Remedy
F 001
Electronic outlets overloaded
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 004
Dimming sensor defective
Call customer service.
F 005
Protective motor switch on high pressure pumps was triggered
Reset motor protection switch; call Customer
Service if the problem recurs.
F 006
Connection to RDS defective
Call customer service.
F 007
The pressure switch air does not report any pressure
Check the compressor and the compressed air
lines.
F 010
No connection to pump electronics at washing station 1
Call customer service.
F 011
Electronic outlets at washing station 1 overloaded
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 012
Current pickup of high pressure pump at washing station 1 too high
F 013
Current pickup of high pressure pump at washing station 1 too low
See "Faults on high pressure pumps"
F 014
Contact of high pressure pump at washing station 1 stuck
Call customer service.
F 015
Semiload valve at washing station 1 defective
F 016
Coiling protection contact of high pressure pump washing station 1
has triggered.
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 017
Oil level of high pressure pump at washing station 1 too low
Refill oil, acknowledge the fault.
F 018
Electronics at washing station 1 defective
Call customer service.
F 020
No connection to remote control electronics at washing station 1
Check the connector of the data cable with the
electronics of the remote control.
F 021
Fault at coin acceptor at washing station 1
Call customer service.
F 022
Check the microswitch on the mechanical coin
acceptor, replace electronic coin acceptor
F 030
No connection to pump electronics at washing station 2
Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 031
Electronic outlets at washing station 2 overloaded
F 032
Current pickup of high pressure pump at washing station 2 too high Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 033
Current pickup of high pressure pump at washing station 2 too low
See "Faults on high pressure pumps"
F 034
Contact of high pressure pump at washing station 2 stuck
Call customer service.
F 035
Semiload valve at washing station 2 defective
63
EN
Summary of Contents for SB MU
